Formation of compressive residual stress by face milling steel AISI 1045
العناوين الأخرى
توليد الاجهادات الضغطية تامتبقية بواسطة التفريز السطحي للصلب (AISI 1045)
المؤلفون المشاركون
al-Fahadawy, Samir Zaydan Khalaf
al-Rabii, Samir Ali Amin
al-Khazraji, Ahmad Nayif Ibrahim
المصدر
al-Khwarizmi Engineering Journal
العدد
المجلد 11، العدد 1 (31 مارس/آذار 2015)، ص ص. 40-50، 11ص.
الناشر
جامعة بغداد كلية هندسة الخوارزمي
تاريخ النشر
2015-03-31
دولة النشر
العراق
عدد الصفحات
11
التخصصات الرئيسية
الموضوعات
الملخص AR
ترتبط إجهادات التشغيل بشكل وثيق جداً مع عوامل القطع و الأشكال الهندسية لأدوات القطع.
يهدف عمل هذا البحث إلى التحقق من تأثير سرعة القطع و معدل التغذية و عمق القطع على الإجهاد المتبقي السطحي للصلب (AISI 1045) بعد عملية التفريز الوجهي.
تم قياس الإجهاد المتبقي على سطح المشغولة بعد كل عملية تفريز باستخدام تقنية حيود الأشعة السينية (XRD).
تم تطبيق برنامج تصميم التجارب (DOE) باستخدام تقنية منهجية الاستجابة السطحية (RSM) بتصميم دوار مركب مركزي (CCD) لبناء نموذج رياضي لإيجاد العلاقة بين المتغيرات الداخلة و الاستجابة.
أظهرت النتائج بأن كلاً من معدل التغذية و سرعة القطع عوامل مهمة تتحكم بالإجهاد المتبقي السطحي بينما لم يكن لعمق القطع تأثير.
تم عمل نموذج تجريبي من الدرجة الثانية بموثوقية ٩٥ % و وجد توافق جيد بين النتائج العملية و المتنبئة.
بعد ذلك، تم عمل أمثلية عددية خلال برنامج تصميم التجارب لإيجاد أمثل إجهاد متبقي سطحي عند أمثل عوامل قطع اعتماداً على أقصى مطلوبية مستحصلة.
وفقاً لذلك، وجد أن الإجهاد المتبقي السطح الضغطي الأمثل (224.361-) ميجاباسكال عند سرعة قطع (٦٩.٢) م / دقيقة و معدل تغذية (٠.٤) م / دقيقة و عمق قطع (0.4) ملم.
الملخص EN
Machining residual stresses correlate very closely with the cutting parameters and the tool geometries.
This research work aims to investigate the effect of cutting speed, feed rate and depth of cut on the surface residual stress of steel AISI 1045 after face milling operation.
After each milling test, the residual stress on the surface of the workpiece was measured by using X-ray diffraction technique.
Design of Experiment (DOE) software was employed using the response surface methodologv (RSM) technique with a central composite rotatable design to build a mathematical model to determine the relationship between the input variables and the response.
The results showed that both the feed rate and the cutting speed are the significant factors controlling the surface residual stress, while the depth of cut had no influence.
A quadratic empirical model was developed with a 95 % confidence level, and a good agreement was found between the experimental and predicted results.
A numerical optimization was then conducted through DOE program to find the optimum surface residual stress at the optimum cutting parameters, depending on the maximum desirability obtained.
The optimum compressive surface residual stress (-224.361 MPa) was found at cutting speed of 69.2 m / min, feed rate of 0.4 m / min and depth of cut of 0.4 mm.
نمط استشهاد جمعية علماء النفس الأمريكية (APA)
al-Khazraji, Ahmad Nayif Ibrahim& al-Rabii, Samir Ali Amin& al-Fahadawy, Samir Zaydan Khalaf. 2015. Formation of compressive residual stress by face milling steel AISI 1045. al-Khwarizmi Engineering Journal،Vol. 11, no. 1, pp.40-50.
https://search.emarefa.net/detail/BIM-557767
نمط استشهاد الجمعية الأمريكية للغات الحديثة (MLA)
al-Khazraji, Ahmad Nayif Ibrahim…[et al.]. Formation of compressive residual stress by face milling steel AISI 1045. al-Khwarizmi Engineering Journal Vol. 11, no. 1 (2015), pp.40-50.
https://search.emarefa.net/detail/BIM-557767
نمط استشهاد الجمعية الطبية الأمريكية (AMA)
al-Khazraji, Ahmad Nayif Ibrahim& al-Rabii, Samir Ali Amin& al-Fahadawy, Samir Zaydan Khalaf. Formation of compressive residual stress by face milling steel AISI 1045. al-Khwarizmi Engineering Journal. 2015. Vol. 11, no. 1, pp.40-50.
https://search.emarefa.net/detail/BIM-557767
نوع البيانات
مقالات
لغة النص
الإنجليزية
الملاحظات
Includes bibliographical references : p. 48-49
رقم السجل
BIM-557767
قاعدة معامل التأثير والاستشهادات المرجعية العربي "ارسيف Arcif"
أضخم قاعدة بيانات عربية للاستشهادات المرجعية للمجلات العلمية المحكمة الصادرة في العالم العربي
تقوم هذه الخدمة بالتحقق من التشابه أو الانتحال في الأبحاث والمقالات العلمية والأطروحات الجامعية والكتب والأبحاث باللغة العربية، وتحديد درجة التشابه أو أصالة الأعمال البحثية وحماية ملكيتها الفكرية. تعرف اكثر