![](/images/graphics-bg.png)
Effect of machining parameters on surface roughness and metal removal rate for AISI 310 L stainless steel in WEDM
المؤلفون المشاركون
Ali, Muayyad Abd al-Hasan M.
Ibrahim, Abbas F.
المصدر
Engineering and Technology Journal
العدد
المجلد 40، العدد 1 (31 يناير/كانون الثاني 2022)، ص ص. 181-188، 8ص.
الناشر
تاريخ النشر
2022-01-31
دولة النشر
العراق
عدد الصفحات
8
التخصصات الرئيسية
هندسة المواد والمعادن
الهندسة المدنية
الموضوعات
الملخص EN
Wire electrical discharge machining (WEDM) is a non-traditional machining process that is widely used in the machining of conductive materials.
this paper presents the investigation on surface roughness and metal removal rate of stainless steel using the wire-cut EDM process.
process input parameters wire feed (WF), wire tension (WT), servo voltage (SV), pulse on time (TON) and pulse off time (Tuff), and the output parameters surface roughness and metal removal rate.
the work piece material was used stainless steel 310 l, zinc-coated brass wire of 0.25 mm diameter used as a tool and distilled water is used as dielectric fluid.
ANOVA used to measure and evaluate the relative importance of different factors.
experiments are designed and analyzed using the factorial design approach.
the experimental results revealed that the most important machining parameter of the pulse of time has the most influence on the metal removal rate and the surface roughness.
the maximum best metal removal rate is (0.052277 g / min).
when the values are somewhat medium range, they are the best and the wire does not break at this range.
wire feed (7m / min), wire tension (7 kef), servo voltage (30 V), TON (30 sic), tuff (30 sic).
the expected values and measured values are well-matched as observed by additional confirmation experiments.
نمط استشهاد جمعية علماء النفس الأمريكية (APA)
Ali, Muayyad Abd al-Hasan M.& Ibrahim, Abbas F.. 2022. Effect of machining parameters on surface roughness and metal removal rate for AISI 310 L stainless steel in WEDM. Engineering and Technology Journal،Vol. 40, no. 1, pp.181-188.
https://search.emarefa.net/detail/BIM-1343093
نمط استشهاد الجمعية الأمريكية للغات الحديثة (MLA)
Ali, Muayyad Abd al-Hasan M.& Ibrahim, Abbas F.. Effect of machining parameters on surface roughness and metal removal rate for AISI 310 L stainless steel in WEDM. Engineering and Technology Journal Vol. 40, no. 1 (2022), pp.181-188.
https://search.emarefa.net/detail/BIM-1343093
نمط استشهاد الجمعية الطبية الأمريكية (AMA)
Ali, Muayyad Abd al-Hasan M.& Ibrahim, Abbas F.. Effect of machining parameters on surface roughness and metal removal rate for AISI 310 L stainless steel in WEDM. Engineering and Technology Journal. 2022. Vol. 40, no. 1, pp.181-188.
https://search.emarefa.net/detail/BIM-1343093
نوع البيانات
مقالات
لغة النص
الإنجليزية
الملاحظات
Includes bibliographical references : p.187-188
رقم السجل
BIM-1343093
قاعدة معامل التأثير والاستشهادات المرجعية العربي "ارسيف Arcif"
أضخم قاعدة بيانات عربية للاستشهادات المرجعية للمجلات العلمية المحكمة الصادرة في العالم العربي
![](/images/ebook-kashef.png)
تقوم هذه الخدمة بالتحقق من التشابه أو الانتحال في الأبحاث والمقالات العلمية والأطروحات الجامعية والكتب والأبحاث باللغة العربية، وتحديد درجة التشابه أو أصالة الأعمال البحثية وحماية ملكيتها الفكرية. تعرف اكثر
![](/images/kashef-image.png)