Experimental and theoretical analysis of flexural capacity of steel fiber reinforced concrete beam on flexible mat foundation

العناوين الأخرى

التحليل التجريبي و النظري لقدرة الانحناء لجسر من الخرسانة المسلحة بالألياف المعدنية على أساس حصيرة مرنة

مقدم أطروحة جامعية

Abbas, Ali Kazim

مشرف أطروحة جامعية

al-Abd Allah, Sad Farhan Ibrahim

الجامعة

جامعة الإسراء

الكلية

كلية الهندسة

القسم الأكاديمي

إدارة المشاريع الهندسية

دولة الجامعة

الأردن

الدرجة العلمية

ماجستير

تاريخ الدرجة العلمية

2022

الملخص العربي

يتم استخدام الألياف المستخدمة في الخرسانة على نطاق واسع ، حيث يمكنها تعزيز خصائص القوة و المرونة.

في هذا البحث ، تم استخدام ألياف الصلب في ثلاث نسب مختلفة في ثلاث مجموعات )أ ، ب ، ج) (0% ، 0.5 ,%1.5 %) لفحص قيمة إزاحة الحمل للحزم على أساس حصير.

يتكون البرنامج التجريبي من كمرتين و ثلاثة مكعبات لكل نسبة من الألياف الفولاذية.

أظهرت النتائج أن الكمرات التي تحتوي على 0% من الألياف الفولانية تمت الإشارة إليها كعينات تحكم تم فحص مسافتين للركاب في عوارض : 50 مم و 100 مم.

الهدف من هذه الدراسة هو التحقق من النسبة المئوية المثلى لألياف الصلب في SFRC على أساس حصير و دراسة السعة القصوى للحمل العوارض SFRC مقارنة بعوارض الخرسانة المسلحة التقليدية على أساس حصيرة.

فشل )A1 تباعد 50 مل) عند 178 كيلو نيوتن مع إزاحة 4.5 مم ، بينما كان أعلى حمولة 182 كيلو نيوتن مع إزاحة 4.5 مم في عينة) A2 تباعد 100 مم).

تظهر الحزمة التحليلية التي لا تحتوي على ألياف فولاذية حمل عطل عند 181 كيلو نيوتن مع إزاحة 4 مم العينات التي تحتوي على 0.5% من الألياف الفولاذية في )B1 تباعد 50 مم) و) B2 تباعد 100 مل (لهما نفس حمل الفشل تقريبا، كان متوسط حمل الفشل 229 كيلو نيوتن بمتوسط إزاحة 6.4 هم تظهر الحزمة التحليلية التي تحتوي على %0.5% من الألياف الفولاذية حمولة عطل عند 217 كيلو نيوتن مع إزاحة 5.5 مم.

العينات التي تحتوي على 1.5% من الألياف الفولانية).

C1 تباعد 50 مم) فشل عند 195 كيلو نيوتن مع إزاحة 6.1 مم، بينما C2 تباعد) 100مم( به حمل فشل عند 198 كيلو نيوتن مع إزاحة 5.9 مم تظهر الحزمة التحليلية التي تحتوي على 1.5% من الألياف الفولاذية حمولة عطل عند 192 كيلو نيوتن مع إزاحة 4.7 مم في ABAQUS ، يكون لمحاكاة العينات نفس اتجاه العينات التجريبية العينات التي تحتوي على 0.5% من الألياف الفولاذية تحمل أكبر حمولة ، في حين أن العينات التي تحتوي على 0% من الألياف الفولانية لديها أقل حمولة كان تأثير جرعة الألياف الفولاذية واضحا في المجموعتين B و C المجموعة C التي تحتوي على 1.5 في المائة.

من الألياف الفولاذية لديها حمل فشل أقل من 0.5 في المائة (المجموعة (ب) ؛ ويعزى ذلك إلى استبدال الألياف الفولاذية لتحل محل الركام الخشن بالطبع.

الملخص الإنجليزي

The fiber used in concrete is widely used since it can enhance strength and elastic properties.

In this research, steel fibers were used in three different percentages in three groups (A, B, and C) (0%, 0.5%, and 1.5 %) to investigate the loaddisplacement value for the beams are on mat foundation.

The experimental program consists of two beams and three cubes for each percentage of steel fiber.

The results showed that beams that contained 0% of steel fiber were referred as to control specimens.

Two spacings of stirrups were investigated in beams: 50 mm and 100 mm.

The objective of this study is to investigate the optimum percentage of steel fibers in SFRC on a mat foundation and to study the maximum load capacity of SFRC beams compared with conventional reinforced concrete beams on mat foundation.

A1 (50 mm spacing) failed at 178 kN with 4.5 mm displacement, while the highest load was 182 kN with 4.5 mm displacement in an A2 (100 mm spacing) specimen.

The analytical beam with no steel fiber shows a failure load at 181 kN with 4 mm displacement.

Specimens that have 0.5% of steel fiber in B1 (50 mm spacing) and B2 (100 mm spacing) have almost the same failure load.

The average failure load was 229 kN with an average displacement of 6.4 mm.

The analytical beam with 0.5% steel fiber shows a failure load of 217 kN with 5.5 mm displacement.

Specimens that have 1.5% steel fiber C1 (50 mm spacing) failed at 195 kN with 6.1 mm displacement, while C2 (100 mm spacing) has a failure load of 198 kN with 5.9 mm displacement.

The analytical beam with 1.5% of steel fiber shows a failure load of 192 kN with 4.7 mm displacement.

In ABAQUS, the simulation of specimens has the same trend as experimental specimens.

The specimens that have 0.5% of steel fiber have the most significant load, while the specimens with 0% of steel fiber have the lowest load.

The effect of steel fiber dosage was apparent in the B and C groups.

The C group with 1.5 percent of steel fiber has a smaller failure load than 0.5 percent (B group); this is attributed to the replacement of steel fiber to take the place, of course, aggregate.

التخصصات الرئيسية

الهندسة المدنية

عدد الصفحات

46

قائمة المحتويات

Table of contents.

Abstract.

Abstract in Arabic.

Chapter One : Introduction.

Chapter Two : Literature review.

Chapter Three : Research methodology.

Chapter Four : Data analysis and results.

Chapter Five : Discussion, recommendation, and conclusion.

References.

نمط استشهاد جمعية علماء النفس الأمريكية (APA)

Abbas, Ali Kazim. (2022). Experimental and theoretical analysis of flexural capacity of steel fiber reinforced concrete beam on flexible mat foundation. (Master's theses Theses and Dissertations Master). Isra University, Jordan
https://search.emarefa.net/detail/BIM-1440521

نمط استشهاد الجمعية الأمريكية للغات الحديثة (MLA)

Abbas, Ali Kazim. Experimental and theoretical analysis of flexural capacity of steel fiber reinforced concrete beam on flexible mat foundation. (Master's theses Theses and Dissertations Master). Isra University. (2022).
https://search.emarefa.net/detail/BIM-1440521

نمط استشهاد الجمعية الطبية الأمريكية (AMA)

Abbas, Ali Kazim. (2022). Experimental and theoretical analysis of flexural capacity of steel fiber reinforced concrete beam on flexible mat foundation. (Master's theses Theses and Dissertations Master). Isra University, Jordan
https://search.emarefa.net/detail/BIM-1440521

لغة النص

الإنجليزية

نوع البيانات

رسائل جامعية

رقم السجل

BIM-1440521