Flow separation of axial compressor cascade blades

المؤلفون المشاركون

al-Tai, Akram Kh.
Habib, Sabah Falih

المصدر

Journal of Engineering

العدد

المجلد 16، العدد 2 (30 يونيو/حزيران 2010)، ص ص. 4877-4895، 19ص.

الناشر

جامعة بغداد كلية الهندسة

تاريخ النشر

2010-06-30

دولة النشر

العراق

عدد الصفحات

19

التخصصات الرئيسية

الهندسة الميكانيكية

الموضوعات

الملخص AR

تم في هذا البحث إجراء دراسة عملية و نظرية لتأثير انفصال الجريان على أداء الريشتين المتعاقبتين للضاغطة المحورية من نوع [NACA 65_ (12)10].

الجزء العملي يتضمن تصنيع ثلاث ريش من مادة الخشب، و تر كل ريشة (100 ملم) لكن إحدى الريش ذات عرض (90 ملم) لاختبارات النفق الدخاني و الريشتين المتبقتين ذواتا عرض (380 ملم) لاختبارات النفق الهوائي.

تربط الريشتين المستخدمتين النفق الهوائي بآلية مناسبة لكي تثبت بمنقلة النفق و بالتالي يمكن تدويرها بالزوايا المطلوبة.

تم اختبار متعاقبة الريشتين في نفق هوائي تحت صوتي واطى لعدد رينولد (Re=239605) المحسوب على أساس السرعة القصوى (35 م / ثا) و طول وتر الريشة.

لقد تم قياس الضغط الكلي و الضغط الاستاتيكي للنقاط المختارة بين ريشتي الضاغطة لخمس زوايا انحراف هي (4,.,4-8-و12-) باستخدام مانوميتر متعدد الأنابيب و أنبوب بيتوت-أستاتي.

تم أختبار الريشة الصغيرة (ذات عرض 90ملم) باستخدام النفق الدخاني لرؤية السلوك الحقيقي لإنفصال الجريان.

الدراسة النظرية تتضمن استخدام البرنامج الجاهز (FLUENT V6.2) لمحاكات الجريان بين الريشتين.

أظهرت الدراسة بأن الأنفصال يبدأ عندما تكون زوايا الأنحراف (4-) حيث يحدث على السطح العلوي للريشة السفلى و بمسافة (96 % من الوتر عمليا و 98 % من الوتر نظريا) من الدخول الى الخروج للمتعاقبة.

و بعد ذلك تزداد منطقة الأنفصال بازدياد زواية الانحراف (stagger angle) (باتجاه عقرب الساعة) حتى تصل إلى (61 % من الوتر عمليا و 63 % من الوتر نظريا) من الدخول الى الخروج عند زواية أنحراف (12-) و هذا ما يوضحه اختبار النفق الدخاني.

يؤثر الأنفصال على أداء الريشتين المتعاقبتين حيث تقل نسبة الضغط (الضغط الستاتيكي الخارج الى الضغط التساتيكي الداخل) بأزدياد منطقة الأنفصال.

و بعد ذلك تم حساب المدى الشغال لزوايا الأنحراف.

الذي وجد ضمن المدى (من -18 الى 36).

أن سلوك الجريان بين الريشتين يبين بأن الريشتين المتعاقبتين تعملان كبوق متقارب- متباعد.

تمت مقارنة النتائج النظرية مع النتائج العملية وجد تقارب جيد بين تلك النتائج.

الملخص EN

An experimental and theoretical investigation of the effect of flow separation on the performance of a cascade NACA 65_(12)10 axial compressor blade has been carried out.

The experimental work includes the fabrication of three blades from wood, each having a chord (100mm) but one of these blades having a span of (90mm) for smoke tunnel testing and the other two blades having a span of (380mm) for wind tunnel testing.The two blades were connected by suitable mechanism in order to be fixed in the wind tunnel protractor and rotated in the required stagger angle.

The cascade was tested in an open type low-speed subsonic (Mach number=0.117) wind tunnel, for Reynolds number (Re=239605) based on maximum velocity (35 m/s) and airfoil chord length.

The total and static pressures were measured in selected points between the two blades for stagger angles of (4 , 0 ,-4 ,-8 and -120) by using a multi-tube manometer and a pitot static tube.

The small blade (90mm span) is tested in the smoke tunnel to visualize the real behavior of flow separation.

The theoretical work includes using the software FLUENT (V6.2) to simulate the flow between the two blades.

The study shows that the flow separation begins when the cascade are inclined at a stagger angle of (-4 ) on the suction side of the lower blade at a position (96%chord experimentally and 98%chord theoretically).

Then, the separation zone increases with increased stagger angle (in clockwise direction) and reach to the position (61%chord experimentally and 63%chord theoretically) at a stagger angle (-12 ).These results are validated by a smoke tunnel tests.This separation affects the performance of the compressor, where the static pressure ratio ( / ) decreases as the separation zone gets bigger.

The range of working stagger angle is then calculated.

It was found in the range (-18 to 36 ).

The flow behavior between the two blades shows that the blade-to-blade configuration works as nozzle-diffuser.

The theoretical results were compared with the experimental results and good agreement was obtained.

نمط استشهاد جمعية علماء النفس الأمريكية (APA)

al-Tai, Akram Kh.& Habib, Sabah Falih. 2010. Flow separation of axial compressor cascade blades. Journal of Engineering،Vol. 16, no. 2, pp.4877-4895.
https://search.emarefa.net/detail/BIM-288258

نمط استشهاد الجمعية الأمريكية للغات الحديثة (MLA)

al-Tai, Akram Kh.& Habib, Sabah Falih. Flow separation of axial compressor cascade blades. Journal of Engineering Vol. 16, no. 2 (Jun. 2010), pp.4877-4895.
https://search.emarefa.net/detail/BIM-288258

نمط استشهاد الجمعية الطبية الأمريكية (AMA)

al-Tai, Akram Kh.& Habib, Sabah Falih. Flow separation of axial compressor cascade blades. Journal of Engineering. 2010. Vol. 16, no. 2, pp.4877-4895.
https://search.emarefa.net/detail/BIM-288258

نوع البيانات

مقالات

لغة النص

الإنجليزية

الملاحظات

Includes bibliographical references : p. 4895

رقم السجل

BIM-288258