Influence of the butt joint design of TIG welding on the thermal stresses
العناوين الأخرى
تأثير تصميم وصلة اللحام باستخدام قطب التنكستن على الاجهادات الحرارية
المؤلفون المشاركون
Amin, Hani Aziz
al-Janabi, Khayriyah Salman Hasan
Salah, Muwaffaq Mahdi
المصدر
Engineering and Technology Journal
العدد
المجلد 29، العدد 14 (31 ديسمبر/كانون الأول 2011)، ص ص. 2841-2858، 18ص.
الناشر
تاريخ النشر
2011-12-31
دولة النشر
العراق
عدد الصفحات
18
التخصصات الرئيسية
الموضوعات
الملخص AR
في هذا البحث تم دراسة تأثير تصميم وصلة اللحام على الاجهادات الحرارية لفولاذ كاربوني نوع St-37 حيث تم اللحام بطريقة القوس الكهربائي باستخدام قطب التنكستن و وجود غلاف غلاف غازي للحصول على وصلات لحام ت تناكبية و اجريت لها عملية تحضير بالزوايا v (º30 ,º (90º, 60º, 45 من جهة واحدة حيث أن تحليل الأجهادات الحرارية تم وفق مصدر حراري متحرك.
لقد تم إعداد موديل عددي من خلال برنامج AMSYS12, أعتمد نموذج العددي حل معادلة الطاقة الثلاثية الأبعاد و لمصدر حراري متحرك, لمواصفات فيزيائية متغيرة مع درجة الحرارة، تغير الطور و باعتبار وجود مصدر حراري متحرك و خواص تاموتد معتمد على درجة الحرارة، أن توزيع درجة الحرارة و الأجهادات الحرارية تم أيجادها لمنطقة اللحام دالة للوقت.
و قد تم إستنتاج أن تصميم حافة اللحام لها تأثير كبير على منطقة اللحام حيث كلما كبرت زاوية الحافة فإن العيوب سوف تقل بسبب زيادة كمية الحرارة في منطقة اللحام.
و قد تم الإستنتاج بإنه يتم اللحام الأسماك الأقل من 6 ملم بدون زيادة تحضيرية بسبب زيادة الإجهادات الحرارية التي تتولد نتيجة زوايا اللحام حيث أن على توزيع حراري كان عند زاوية لحام °60 و أقل توزيع كان عند °90.
الملخص EN
The aim of this paper is to demonstrate the influence of the single butt joint design of TIG welding on the thermal stresses for carbon steel type St-37.
The butt welding was performed by V angles 30°, 45°, 60° and 90° and the thermal stresses analysis is based on the local moving heat flux.
The numerical model developed by ANSYS12 software based on solving the three dimensional energy equation, considering moving heat source and temperature dependent material properties.
Temperature and stresses distributions were obtained function of time.
From the results, it is evident that the joint design has an important role in the welding process, when the edge angle of the welding region gets bigger, the faults get less due to increase of heat flux in the welding region.
It can be concluded that the specimen with less than 6mm thickness can be welded without edge angle preparation, due to increase the thermal stresses when edge angle is evident and higher thermal stresses distribution was at edge angle 60˚ and lowest thermal stresses distribution was at 90°.
نمط استشهاد جمعية علماء النفس الأمريكية (APA)
Amin, Hani Aziz& al-Janabi, Khayriyah Salman Hasan& Salah, Muwaffaq Mahdi. 2011. Influence of the butt joint design of TIG welding on the thermal stresses. Engineering and Technology Journal،Vol. 29, no. 14, pp.2841-2858.
https://search.emarefa.net/detail/BIM-289763
نمط استشهاد الجمعية الأمريكية للغات الحديثة (MLA)
Amin, Hani Aziz…[et al.]. Influence of the butt joint design of TIG welding on the thermal stresses. Engineering and Technology Journal Vol. 29, no. 14 (2011), pp.2841-2858.
https://search.emarefa.net/detail/BIM-289763
نمط استشهاد الجمعية الطبية الأمريكية (AMA)
Amin, Hani Aziz& al-Janabi, Khayriyah Salman Hasan& Salah, Muwaffaq Mahdi. Influence of the butt joint design of TIG welding on the thermal stresses. Engineering and Technology Journal. 2011. Vol. 29, no. 14, pp.2841-2858.
https://search.emarefa.net/detail/BIM-289763
نوع البيانات
مقالات
لغة النص
الإنجليزية
الملاحظات
Includes appendices : p. 2846-2858
رقم السجل
BIM-289763
قاعدة معامل التأثير والاستشهادات المرجعية العربي "ارسيف Arcif"
أضخم قاعدة بيانات عربية للاستشهادات المرجعية للمجلات العلمية المحكمة الصادرة في العالم العربي
تقوم هذه الخدمة بالتحقق من التشابه أو الانتحال في الأبحاث والمقالات العلمية والأطروحات الجامعية والكتب والأبحاث باللغة العربية، وتحديد درجة التشابه أو أصالة الأعمال البحثية وحماية ملكيتها الفكرية. تعرف اكثر