![](/images/graphics-bg.png)
Study the optimal cutting conditions affecting the copper surface roughness by taguchi technique
العناوين الأخرى
دراسة ظروف القطع المثلى المؤثرة على الخشونة السطحية للنحاس باستخدام طريقة تاكوجي
المؤلف
al-Baghdadi, Bara Muhsin Husayn
المصدر
The Iraqi Journal for Mechanical and Materials Engineering
العدد
المجلد 13، العدد 4 (31 ديسمبر/كانون الأول 2013)، ص ص. 723-733، 11ص.
الناشر
تاريخ النشر
2013-12-31
دولة النشر
العراق
عدد الصفحات
11
التخصصات الرئيسية
الموضوعات
الملخص AR
يهدف البحث إلى إيجاد الظروف المثلى المؤثرة على الخشونة السطحية عند تشغيل النحاس في عملية الخراطة.
تم في هذا البحث استخدام طريقة تاكوجي لإيجاد الظروف المثلى لمتغيرات القطع.
الظروف المستخدمة هنا هي سرعة دوران القطعة و معدل التغذية و نصف قطر مقدمة الأداة حيث تم استخدام فولاذ القطع السريع كأداة قطع، بينما قد تم تثبيت مقدار عمق القطع.
تم تطبيق الخاصية "الأصغر هو الأفضل" بالنسبة لحساب النسبة بين الإشارة إلى الضوضاء (S / N) لكل تجربة.
أيضا تم استخدام تحليل التباين ANOVA، في تحديد أكثر عامل مؤثر من عوامل متغيرات القطع من خلال امتلاكه لأكثر نسبة مشاركة أو مساهمة في العملية.
بينت النتائج بأن التوليفة الأمثل لمتغيرات القطع كانت عند المستويات (1-1-3) و التي تتمثل بسرعة دوران القطعة (1120 دورة في الدقيقة)، و معدل التغذية (0.065 ملم / دورة)، و مصف قطره مقدمة الأداة (4 ملم).
العامل الأكثر أهمية بحسب مساهمته الأكبر و الذي بينه جدول ANOVA هو سرعة دوران القطعة بنسبة مشاركة 58.581 % يليه معدل التغذية و نصف قطر الأداة على التوالي.
الملخص EN
This research aims to find the optimal conditions affecting the surface roughness when copper is turned.
In this work the Taguchi method is used to optimize the cutting parameters.
The parameters considered here are : spindle speed, feed rate, and the tool nose radius while the depth of cut has been fixed during the experiments.
The tool used for conducting the experiment is High Speed Steel (HSS).
Once the surface roughness is measured, the quality characteristic “smaller is the better” is applied to calculate the signal to noise ratio S / N for each experiment.
Also, by using ANOVA output, the factor that has more significant in the process has been determined depending on its percentage of contribution.
The results showed that the optimum combination of levels of the parameters were (3-1-1) that are corresponding to spindle speed (1120 rpm), feed rate (0.065 mm / rev), and tool nose radius (4 mm).
The significant factor that has maximum contribution according to ANOVA results is the spindle speed with 58.581 % followed by feed rate and tool nose radius respectively.
نمط استشهاد جمعية علماء النفس الأمريكية (APA)
al-Baghdadi, Bara Muhsin Husayn. 2013. Study the optimal cutting conditions affecting the copper surface roughness by taguchi technique. The Iraqi Journal for Mechanical and Materials Engineering،Vol. 13, no. 4, pp.723-733.
https://search.emarefa.net/detail/BIM-363674
نمط استشهاد الجمعية الأمريكية للغات الحديثة (MLA)
al-Baghdadi, Bara Muhsin Husayn. Study the optimal cutting conditions affecting the copper surface roughness by taguchi technique. The Iraqi Journal for Mechanical and Materials Engineering Vol. 13, no. 4 (2013), pp.723-733.
https://search.emarefa.net/detail/BIM-363674
نمط استشهاد الجمعية الطبية الأمريكية (AMA)
al-Baghdadi, Bara Muhsin Husayn. Study the optimal cutting conditions affecting the copper surface roughness by taguchi technique. The Iraqi Journal for Mechanical and Materials Engineering. 2013. Vol. 13, no. 4, pp.723-733.
https://search.emarefa.net/detail/BIM-363674
نوع البيانات
مقالات
لغة النص
الإنجليزية
الملاحظات
Includes bibliographical references : p. 732-733
رقم السجل
BIM-363674
قاعدة معامل التأثير والاستشهادات المرجعية العربي "ارسيف Arcif"
أضخم قاعدة بيانات عربية للاستشهادات المرجعية للمجلات العلمية المحكمة الصادرة في العالم العربي
![](/images/ebook-kashef.png)
تقوم هذه الخدمة بالتحقق من التشابه أو الانتحال في الأبحاث والمقالات العلمية والأطروحات الجامعية والكتب والأبحاث باللغة العربية، وتحديد درجة التشابه أو أصالة الأعمال البحثية وحماية ملكيتها الفكرية. تعرف اكثر
![](/images/kashef-image.png)