The effect of cutting tool vibration on surface roughness of work piece in dry turning operation
المؤلفون المشاركون
Khoshnaw, Yunus K.
Kassab, Safeen Y.
المصدر
Engineering and Technology Journal
العدد
المجلد 25، العدد 07 (30 سبتمبر/أيلول 2007)، ص ص. 879-889، 11ص.
الناشر
تاريخ النشر
2007-09-30
دولة النشر
العراق
عدد الصفحات
11
التخصصات الرئيسية
الموضوعات
الملخص AR
هذا البحث لإيجاد علاقة بين اهتزازات قلم القطع و الخشونة السطحية في عملية القطع، تم تحديد عوامل القطع في هذه الدراسة بحيث تكون سرعة القطع (1030، 560، 270 دورة / دقيقة) و عمق القطع (0.2، 0.1 ملم) و معدل التغذية (0.17، 0.13، 0.07 ملم / دورة) و طول قلم القطع (40، 35، 30، 25 ملم), تم أجراء التجارب في ماكنة الخراطة بدون استخدام سائل التبريد، و باستخدام عينات من حديد ذو نسبة كاربون متوسطة عند مختلف حالات القطع، عدم استخدام سائل التبريد يمثل حالة جيدة لعملية القطع، حيث يعطي وضعية جيدة لحصول على اهتزازات القطع، و النتائج يكون أكثر وضوحا و دقيقا بين اهتزازات و خشونة السطحية, نتائج التحليل في هذه الدراسة يوضح بأن الخشونة السطحية جيدة يكون في حالة معدل التغذية أقل أو يساوي إلى 0.13 ملم / دورة أما الخشونة السطحية غير جيدة متشابهة (عند بروز أقل أو يساوي 30 ملم)، النتائج في هذه الدراسة يبين بأن لسرعة القطع تأثير صغير جدا على الخشونة السطحية مقارنة مع تأثير معدل التغذية, أما عمق القطع فأن تأثيرها ليست ملحوظة على الخشونة السطحية, هذه النتائج يمكن حصول عليها عند عدم لصق الرايش على القلم أو عدم حصول أي ضرر في رأس القلم, في النهاية فأن النتائج العملية يبين بأن هناك علاقة جيدة بين اهتزاز القلم و الخشونة السطحية، و يمكن استخدامها لسيطرة على الخشونة السطحية لشغله في عمليات اللاإنتاجية.
الملخص EN
This study is to find a correlation between surface roughness and cutting tool vibration in turning.
The ranges of process cutting parameters in the present study are limited : cutting speed (34, 70, 130 m / min), depth of cut (0.1, 0.2mm), feed rate (0.07, 0.13, 0.17mm / rev) and tool overhanging (25, 30, 35, 40mm).
The data are generated by lathe dry turning of medium carbon steel samples at different levels of the mentioned above parameters.
Dry cutting tests (without using cutting fluid) are conducted to simulate a good turning, the dry turning provided a clean environment to obtain undisturbed clear cutting vibration, which results in more accurate and clear correlation between cutting vibrations and roughness.
The analysis of variance reveal in this study is that the best surface roughness condition is achieved at a low (feed rate less and equal 0.13mm / rev), and with smaller tool overhang less and equal 30mm).
The results also show that the cutting speed has small effect on surface roughness than feed rate and tool overhang.
The depth of cut has not a significant effect on surface roughness in this study.
Above results can be obtained when there is no built up edge and no damage of the tool tip.
Finally experimental results have shown good correlation between the cutting tool vibration and surface roughness which can be used to control the finish surface of the workpieces during the mass production.
نمط استشهاد جمعية علماء النفس الأمريكية (APA)
Kassab, Safeen Y.& Khoshnaw, Yunus K.. 2007. The effect of cutting tool vibration on surface roughness of work piece in dry turning operation. Engineering and Technology Journal،Vol. 25, no. 07, pp.879-889.
https://search.emarefa.net/detail/BIM-52710
نمط استشهاد الجمعية الأمريكية للغات الحديثة (MLA)
Kassab, Safeen Y.& Khoshnaw, Yunus K.. The effect of cutting tool vibration on surface roughness of work piece in dry turning operation. Engineering and Technology Journal Vol. 25, no. 07 (2007), pp.879-889.
https://search.emarefa.net/detail/BIM-52710
نمط استشهاد الجمعية الطبية الأمريكية (AMA)
Kassab, Safeen Y.& Khoshnaw, Yunus K.. The effect of cutting tool vibration on surface roughness of work piece in dry turning operation. Engineering and Technology Journal. 2007. Vol. 25, no. 07, pp.879-889.
https://search.emarefa.net/detail/BIM-52710
نوع البيانات
مقالات
لغة النص
الإنجليزية
الملاحظات
Includes bibliographical references : p. 883-884
رقم السجل
BIM-52710
قاعدة معامل التأثير والاستشهادات المرجعية العربي "ارسيف Arcif"
أضخم قاعدة بيانات عربية للاستشهادات المرجعية للمجلات العلمية المحكمة الصادرة في العالم العربي
تقوم هذه الخدمة بالتحقق من التشابه أو الانتحال في الأبحاث والمقالات العلمية والأطروحات الجامعية والكتب والأبحاث باللغة العربية، وتحديد درجة التشابه أو أصالة الأعمال البحثية وحماية ملكيتها الفكرية. تعرف اكثر