Surface roughness evaluation in WEDM using Taguchi parameter design method
المؤلفون المشاركون
Najm, V. N.
Aghdeab, Shukri H.
Salih, A. M.
المصدر
Engineering and Technology Journal
العدد
المجلد 36، العدد 1A (31 يناير/كانون الثاني 2018)، ص ص. 60-64، 5ص.
الناشر
تاريخ النشر
2018-01-31
دولة النشر
العراق
عدد الصفحات
5
التخصصات الرئيسية
تكنولوجيا المعلومات وعلم الحاسوب
الموضوعات
الملخص EN
Machining of hard metal is difficult by conventional method to obtain high accuracy where the dimensional accuracy is the main factor.
Wire electrical discharge machining (WEDM) extensively used, which is mostly used in machining of conductive materials by using precisely controlled sparks that occur between a very thin wire and a workpiece in the presence of a dielectric fluid.
This study serves in studying surface roughness (SR) of high speed steel (HSS) using taguchi method to design the experiment, this was achieved with utilizing different wire cut machining parameters and study the behavior of these control parameters such as pulse duration (μs), pulse interval (μs), Servo feed and Servo voltage (V) on surface roughness.
It can be noticed that when servo voltage and servo feed increase the surface roughness decreases and when pulse duration and pulse interval increase the surface roughness increases too, and It was found with using taguchi parameter design that the best machining variables of combination setting is Servo Voltage (22) volts, Pulse on time (110) μs, servo feed (450) mm/min and Pulse off time (30) μs to reach to the minimum value of surface roughness and hence better surface finish
نمط استشهاد جمعية علماء النفس الأمريكية (APA)
Aghdeab, Shukri H.& Najm, V. N.& Salih, A. M.. 2018. Surface roughness evaluation in WEDM using Taguchi parameter design method. Engineering and Technology Journal،Vol. 36, no. 1A, pp.60-64.
https://search.emarefa.net/detail/BIM-812378
نمط استشهاد الجمعية الأمريكية للغات الحديثة (MLA)
Aghdeab, Shukri H.…[et al.]. Surface roughness evaluation in WEDM using Taguchi parameter design method. Engineering and Technology Journal Vol. 36, no. 1A (2018), pp.60-64.
https://search.emarefa.net/detail/BIM-812378
نمط استشهاد الجمعية الطبية الأمريكية (AMA)
Aghdeab, Shukri H.& Najm, V. N.& Salih, A. M.. Surface roughness evaluation in WEDM using Taguchi parameter design method. Engineering and Technology Journal. 2018. Vol. 36, no. 1A, pp.60-64.
https://search.emarefa.net/detail/BIM-812378
نوع البيانات
مقالات
لغة النص
الإنجليزية
الملاحظات
Includes bibliographical references : p. 64
رقم السجل
BIM-812378
قاعدة معامل التأثير والاستشهادات المرجعية العربي "ارسيف Arcif"
أضخم قاعدة بيانات عربية للاستشهادات المرجعية للمجلات العلمية المحكمة الصادرة في العالم العربي
تقوم هذه الخدمة بالتحقق من التشابه أو الانتحال في الأبحاث والمقالات العلمية والأطروحات الجامعية والكتب والأبحاث باللغة العربية، وتحديد درجة التشابه أو أصالة الأعمال البحثية وحماية ملكيتها الفكرية. تعرف اكثر