Evaluation of poultry feed quality in Khartoum state, Sudan

Abstract EN

This study was carried out to assess the quality of poultry feeds sold for poultry fanners compared to National Research Council (NRC.

1994) and Sudanese Standards and Metrological Organization (SSMO.

2015) standards.

Chemical analysis using AOAC (1990 ) was used to assess the quality of 17 samples of poultry feeds ( 6 broiler starter .

6 broiler finisher and 5 samples layer feed) collected randomly from six factories (A, B.

C.

D.

E and F) during 2013.

Dry matter (DM %).

crude protein [CP%].

ether extract (EE %), crude fiber (CF %).

ash% and aflatoxin (ppb) were recorded.

Metabolizable energy (ME) was calculated by the equation of Lodhi (1976).Major minerals Ca%.

Zn%.

K% and Na% and oligo elements Fe mg/kg, Mn mg leg and Mn mg/kg were determined.

The analytical results revealed that in most broiler starter feeds CP content fall within the acceptable level (23%) except feed E showed lower CP percent (18.3%).The CP of broiler finisher feeds were of 20% feed A to 23.16% feed B.

For broiler starter feed the metabolizable energy (ME) content ranges from 2914 Kca/Kg feed E to 3282 Kca/Kg feed F and the finisher feeds range from 2747 Kca/Kg feed E to 3349 Kca/Kg feed A Most of feeds had a satisfactory levels of ME except feed E which contained a little bit low ME .The mean CF content of all feeds varied from 3.5% to 5.5% whereas the maximum recommended level is < 5 %.DM contents were within the acceptable ranges of (NRC, 1994 and SSM0.2015).In both broiler starter and finisher feeds, feed A.

D.

and F had slightly higher fat content ( 6.6 - 7.5 %) in contrast feed B.

C and E had lower fat content compared to the required levels.

Low levels of ash 2.62 - 7.05% than the required level (8 %) were recorded in all broiler starter and finisher feeds except broiler starter feed E showed higher level of ash (14.6 %) than the recommendation Higher Aflatoxin (ppb) were recorded in broiler starter feeds A, C and D (49.15, 35.63, 35.31 ppb ) and broiler finisher feeds B and C (27.22 and 43.59 ppb) compared to the permitted level (<20 ppb).

For all layer feeds the average CP content range between 17.86% to 18.6.% except feed D contained higher CP (20.98%) while the recommendations are around (17 -18%).Meanwrhile.

ME ranges from 2679.2 Kcal /Kg to 3127.9KcalKg the recommendations being simated around 2749 Kca / Kg to 2900 Kcal/Kg.

Fat and DM contents fall within the acceptable ranges (2-5% fat) and (90 - 95% DM) .On the other hand, all feeds are generally high in ash content (10.33 - 20.85%) compared to the recommended level (8%).A11 feeds had acceptable ranges of CF (3.5 - 4.5%) and aflatoxin (7.6 - 18.3 ppb ).

For broiler starter feeds Fe.

Mg and Na content were too low compared to the required levels(S0 mgkg.

600mg/kg and 0.2 % respectively).mean while K.

Mn and Zn showed higher values except feed B and C showed lower Zn content (21.3 and 33.63%).Ca content ranges between 0.83 to 0.88% which is almost within the required levels (0.9 to 1%) except feed E contained very high level of Ca (3.4%).On the other hand, higher levels of K.

Na, Mn and Zn were recorded in all broiler finisher feeds except feed B and C recorded lower values of Zn (0.22 and 0.49 %).Low levels of Fe and Mg were noticed in all feeds except feed F contained the recommended level of Fe (80.03mgkg).Ca contents in all feeds are generally satisfactory 0.83 to 0.91%0) except feed D and E contained very low levels of Ca (0.24 and 0.49%).

Generally in all layer feeds Ca.

Fe.

Mg.

Mn and Na contents were lower than the recommended levels except feed D and E showed higher levels of Fe (62.4 and 69.1mgkg).On the contrary K (0.49 - 0.55%) and Zn (55.26 - 92.45%) contents were higher.

Council (NRC) and (SSMO).

On the other hand, minerals content showed significant (P<0.05) differences among dietary’ treatments and most of them were not met the values reported by (NRC) and (SSMO).

It could be concluded that the variations observed among different poultry’ feeds compared to (NRC 1994) and (SSMO 2015) specifications strongly indicates that confirmatory analyses should be conducted at regular intervals to control feed quality.